caution : observe precautions when handling be cause these devices are sensitive to electrostatic discharge wide band spdt switch cmos integra ted circuit ? p d571 3 tk document no. p u 10627ej01v0ds (1st edition) date published september 2006 ns cp(k) description the ? p d571 3 tk is a cmos mmic for wide band spdt (single pole double throw) switch which were developed for mobile communications, wireless communications and another general - purpose rf switching application. this device can operate frequency f rom 0.05 to 2.5 ghz, having the low insertion loss and high isolation. this device is housed in a 6 - pin lead - less minimold (1511) package. and this package is able to high - density surface mounting. features ? s upply voltage : v dd = 1.8 to 3. 6 v (2.8 v ty p.) ? switch control voltage : v cont (h) = 1.8 to 3. 6 v (2.8 v typ.) : v cont (l) = ? 0.2 to +0. 4 v (0 v typ.) ? low insertion loss : l ins 1 = 0. 6 db typ. @ f = 0.05 to 1.0 ghz, v dd = 2.8 v, v cont (h) = 2.8 v , v cont (l) = 0 v : l ins 2 = 0. 8 db typ. @ f = 1 .0 to 2.0 ghz , v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v : l ins 3 = 0. 9 5 db typ. @ f = 2.0 to 2.5 ghz , v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v ? high isolation : isl 1 = 32.5 db typ. @ f = 0.05 to 1.0 ghz, v dd = 2.8 v, v cont (h) = 2.8 v, v con t (l) = 0 v : isl 2 = 2 5 db typ. @ f = 1 .0 to 2. 0 ghz , v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v : isl 3 = 22.5 db typ. @ f = 2.0 to 2.5 ghz, v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v ? h andling power : p in (1 db) = +21.0 dbm typ. @ f = 1.0 g hz, v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v : p in (0.1 db) = + 1 7 .0 dbm typ. @ f = 1 .0 ghz, v dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v ? high - density surface mounting : 6 - pin lead - less minimold package ( 1.5 ? 1. 1 ? 0. 55 mm) applications ? mo bile communications ? wireless communications ? another general - purpose rf switching applications ordering information part number order number package marking supplying form ? pd5713tk - e2 ? pd5713tk - e2 - a 6 - pin lead - less minimold (1511) (pb - free) c3 q ? e mbossed tape 8 mm wide ? pin 1, 6 face the perforation side of the tape ? qty 5 kpcs/reel remark to order evaluation samples, contact your nearby sales office. part number for sample order: ? p d571 3 tk - a
data sheet p u 10 627 ej0 1 v0ds 2 ? p d571 3 tk pin connections and internal block diagram pin no. pin name 1 output1 2 gnd 3 output2 4 v cont 5 input 6 v dd truth table v cont input ? output1 input ? output2 low off on high on off absolute maximum ratings (t a = +25 ? parameter symbol ratings unit su pply voltage v dd ? 0.5 to +4.6 v switch control voltage v cont ? 0.5 to +4.6 v voltage difference v cont (h) ? v d d +0.5 v input power p in + 2 3 dbm operating ambient temperature t a ? 45 to +85 ? c storage temperature t stg ? 5 5 to +150 ? c recommended operat ing range (t a = +25 ? parameter symbol min. typ. max. unit supply voltage v dd +1.8 + 2.8 + 3. 6 v switch control voltage (h) v cont (h) +1.8 +2.8 +3. 6 v switch control voltage (l) v cont (l) ? 0.2 0 + 0. 4 v remark v dd ? 0. 4 v ? v cont (h) ? v dd + 0. 2 v
data sheet p u 10 627 ej0 1 v0ds 3 ? p d571 3 tk electrical characteristics (t a = +25 ? dd = 2.8 v, v cont (h) = 2.8 v, v cont (l) = 0 v, dc cut capacitors = 1 000 pf, unless otherwise specified) parameter symbol test conditions min. typ. max. unit insertion loss 1 l ins 1 f = 0.05 to 1.0 ghz ? 0. 6 0. 8 db insertion loss 2 l ins 2 f = 1.0 to 2.0 ghz ? 0. 8 1.0 db insertion loss 3 l ins 3 f = 2.0 to 2.5 ghz ? 0. 9 5 1.2 db isolation 1 isl 1 f = 0.05 to 1 .0 ghz 30 32.5 ? db isolation 2 isl 2 f = 1 .0 to 2. 0 ghz 22 25 ? db isolation 3 isl 3 f = 2.0 to 2.5 ghz 20 22.5 ? db input return loss rl in f = 0.05 to 2.5 ghz 1 3 17 ? db output return loss rl out f = 0.05 to 2.5 ghz 1 3 17 ? db 0.1 db loss compression p in (0.1 db) f = 1 .0 ghz + 13 . 0 + 1 7 .0 ? dbm input power note 1 1 db loss co mpression p in (1 db) f = 1 .0 ghz ? + 21.0 ? dbm input power note 2 supply current i dd v dd = v cont = 2.8 v, rf off ? 0.01 1.0 ? a switch control current i cont v dd = v cont = 2.8 v, rf off ? 0.01 1.0 ? a switch control speed t sw f = 1.0 ghz ? 3 0 10 0 ns note s 1. p in (0.1 db) is measured the input power level when the insertion loss increases more 0.1 db than that of linear range. 2. p in (1 db) is measured the input power level when the insertion loss increases more 1 db than that of linear range. c aution this device is used it is necessary to use dc cut capacitors. the value of dc cut capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with actual board of your system.
data sheet p u 10 627 ej0 1 v0ds 4 ? p d571 3 tk evaluation ci rcuit remark c0 = 1 000 pf caution this ic has pull down resistance between rf line and gnd, witch fixes electric potential of rf line to 0 v, then the ic cannot be used for dc switching. the application circuits and their parameters are for refer ence only and are not intended for use in actual design - ins.
data sheet p u 10 627 ej0 1 v0ds 5 ? p d571 3 tk illustration of the test circuit assembled on evaluation board using the evaluation board symbol values c1, c2 , c3 1 000 pf c4, c5 1 000 pf
data sheet p u 10 627 ej0 1 v0ds 6 ? p d571 3 tk typical characteristics (t a = + 25 ? dd = 2.8 v, v con t (h) = 2.8 v , v cont (l) = 0 v , p in = 0 dbm, dc cut capacitors = 1 000 pf , unless otherwise specified) remark the graphs indicate nominal characteristics.
data sheet p u 10 627 ej0 1 v0ds 7 ? p d571 3 tk remark the graphs indicate nominal characteristics.
data sheet p u 10 627 ej0 1 v0ds 8 ? p d571 3 tk mounting pad di mensions 6 - pin lead - less minimold (1511) (unit: mm) remark the mounting pad layouts in this document are for reference only .
data sheet p u 10 627 ej0 1 v0ds 9 ? p d571 3 tk package dimensions 6 - pin lead - less minimold (1511) (unit: mm)
10 data sheet pu10627ej01v0ds ? p d571 3 tk recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales office. soldering method soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 ? c or below time at peak temperature : 10 seconds or less time at temperature of 220 ? c or higher : 60 seconds or less preheating time at 120 to 180 ? c : 120 ? 30 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ir260 wave soldering peak temperature (molten solder temperature) : 260 ? c or below time at peak temperature : 10 seconds or less preheating temperature (package surface temperatu re) : 120 ? c or below maximum number of flow processes : 1 time maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ws260 partial heating peak temperature ( terminal temperature) : 350 ? c or below soldering time (per side of device) : 3 seco nds or less maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering methods together (except for partial heating).
|
